Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
We have discovered the article about Tools You Need to Install a New Bathtub directly below on the web and figured it made perfect sense to write about it with you in this article.
Mounting a bathtub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is likewise a reasonably difficult project. If the old tub is readily available, the job can move rapidly; if you have to open a wall to eliminate the old tub as well as position the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub and set in the new one. Make certain you have certified yourself for the work and fit attempting it. Instead of working with a service provider to take control of a halfway-completed project, it is far better to take into consideration utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This article will certainly aid you set up a brand-new bath tub in your washroom if you have currently acquired a new bathtub as well as do not need to alter the setup of your previous water system pipelines.
Your devices and material checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washing machines are in area in between the tap and the sink. Protect the tap in place with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous kind should be linked to the tap finishes initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using the two wood boards under its feet, put the bathtub in the called for position. The wooden boards are practical in equally spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four little points.
The following goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the bath tub till the level reads degree.
To install faucets, fit all-time low of the outermost versatile faucet connector to the proper supply pipe by making a compression join; then do the same for the various other tap.
Switch on the water supply as well as examine all joints as well as brand-new pipework for leaks and tighten them if required. Fill up the tub and also check the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the tub needs to wait until the bath tub has actually been used a minimum of when as this will certainly settle it right into its last placement.
Planning for the Installation
First of all, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to prevent pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, triggering the water to penetrate the wall surface between the bath and the tiling, resulting in problems with wetness and possible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and also cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always fill up the bathtub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealant can break rather early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that review on Installing A Bathtub while browsing on the web. So long as you liked our blog entry plz don't forget to pass it around. Many thanks for taking the time to read it.
Drain issues? Reach out! Report this page